Introduction 

Before being useable as a driveway, walkway, or patio, brick pavers are covered, and power washed. In such circumstances, however, aesthetics take precedence over functionality. 

Brick pavers have swiftly taken the place of concrete and asphalt as the material for constructing fashionable hardscapes around residential properties in all climates. They can do more than just add aesthetic value to a driveway, patio, or sidewalk if they are intended to be permeable. They can also help prevent rainwater from pooling up in areas where it is not supposed to (i.e., with sufficient space between each brick to allow water to naturally percolate into the soil instead of running off the ends of solid pavement).  

To put it more succinctly, these qualities improve a home’s marketability, raising its possible selling price. If you need additional information, don’t be afraid to contact a local paving contractor in Russell Lea. A significant number of people make purchases from him. 

Power washing the brick or paving stone surfaces 

The initial step in bringing the condition of your pavers back to their original glory is to give them a thorough power cleaning using the surface cleaner that is most appropriate. It is advisable that a surface cleaner might be able to distribute the water pressure uniformly across the area to prevent the pavers from being damaged. Because of this method, the bricks or pavers will be fully clean, and the sand and other debris will be wedgable in the gaps. The pavers will also be eliminated as a consequence of this procedure.  

Using Regular Sand Between The Bricks/Paving Stones 

If you wanted to use regular sand instead, it would be less expensive, but that’s about it. In contrast to polymeric sand, normal sand will not solidify into a surface that will prevent weeds from growing through the crevices between your pavers in the same way that polymeric sand will. Even if you use ordinary sand to fill the spaces between your pavers, ants will still find a way to establish a home. If you use regular sand for this project, you will have to do it again the following year because the precipitation will carry it away. 

Layering Polymeric Sand In Between Brick/Paving stones 

A mixture of appropriately graded fine sand and a binder compound (polymer) is useable to fill the spaces between bricks, pavers, and natural stones in hardscapes like patios, driveways, and pathways. Techniseal’s polymeric sand, first useable in 1999, simplifies the process of laying and maintaining stone and brick hardscapes. 

It is recommended by paving contractors of Russell Lea to wait until the paving stones have dried thoroughly after being cleaned with a power washer before putting in the polymeric sand. Wet weather makes it more difficult and time-consuming to shovel sand into the crevices. The best time to do this is on a lovely, dry day after you’ve just power-cleaned the driveway. Putting down the sand to wash it off with water later is a waste of expensive building materials. 

Avoid these common pitfalls when laying polymeric sand over a brick or paver hardscape. 

Although installing polymeric sand does not need rocket science, the quality of the installation significantly impacts the product’s longevity. Considering the expense of the sand and the time it will take to install it, you will want to perform a good job or employ a competent contractor. 

  • Pick out some good sand. 

Pick polymeric sand that doesn’t include portland cement and is high-quality (transparent) polymers. Using high-quality polymeric sand will simplify the application process and produce a more professional result. 

  • Failure to Compact Polymeric Sand 

Polymeric sand is not “settled” when swept into a joint. Lack of compaction of polymeric sand results in voids and air pockets at the joints. It increases your risk of joint damage and cracking. 

  • Excessive or Inadequate Water Use 

The polymers in the polymeric sand need to be activated by water for the sand to “set” correctly. Too much water might wash away the sand and polymers, leaving a mess that would need to be cleanable. On the other hand, insufficient water during this procedure will prevent the polymeric sand from forming a particularly tight bond, leading to loose seams between the pavers. Simply misting the joints with water will do the trick. 

Conclusion 

We are the local Paving Contractor in Russell Lea that you can rely on to do a good job when you need power washing done on your brick or paving stone and installing polymeric sand. As a result, you may have confidence that you will get the most out of your investment since your brick or paver hardscape will be power washed meticulously, and the polymeric sand may be placable precisely underneath. 

Disclaimer: This is generic Information & post; content about the services can be changed from time to time as per your requirements and contract. To get the latest and updated information, contact us today or visit our website.